![]() Variation 2: Connecting to a Home Stereo AmplifierĬonnecting a mixing board to a home stereo amplifier is basically just like hooking the board up to a professional PA amp. If your guitar amp has a line level input, you could safely use that instead of the main jack, but such a setup will never give you the same sound quality, will probably only be monaural (not stereo) and may not provide enough volume. Some people want to connect their mixer to a guitar amplifier, but this is not normally recommended, as the output from the mixing board is too strong for the amp’s guitar input jack, resulting in unexpectedly high, even dangerous, volume levels, extreme distortion and damage to your equipment. The same cables and connectors are used and the same principles apply, and you should be able to follow the directions above with the same results. These are PA speakers which have a power amplifier built into them, eliminating the need for a separate amplifier.Ĭonnecting your audio mixing board to powered speakers is exactly the same as connecting to an outboard PA amplifier. In some cases, you may want to use “active” loudspeakers. If your amplifier is connected to speakers, and your mixer has an audio signal running through it, you should have sound! Variation 1: Connecting to Powered Speakers Make sure that all volume controls are all the way down and then turn first the mixer and then the PA amplifier ON and slowly turn up the output level controls. Plug Connectors in the Amplifier Yamaha MA2120 Amplifier Stereo Input Jacks – Image courtesy of Yamaha Corp.īring the other ends of the cables over to the amplifier and plug the right and left channel RCA plugs into the amp’s respective connectors. Plug the right channel cable’s Phone plug into the mixer’s right channel output jack and the left channel cable into the mixer’s left channel output jack. Turn your mixing board and amplifier OFF to prevent any damage or noise when connecting. Plug Connectors in the Mixer Yamaha MG10/2 ST OUT (Main Stereo Output) – Image courtesy of If you can’t easily recognize what type of connector you need, the owner’s manual will tell you, and the right cables should be readily available from the shop where you purchased your equipment, or from any pro audio retailer. ![]() Mono Phone Plug – Image courtesy of RCA Connectors – Image courtesy of You will need two of these cables – for the right and the left channels – and the cables need to be long enough to reach from the mixer to wherever the amplifier is positioned. So for this example, you will need cables with male Phone jacks on one end and male RCA jacks on the other. In our case, the Yamaha mixer uses mono female Phone plugs (see pic) and the Yamaha amplifier uses female RCA input connectors (see pic). Check Type of Connectorsįirst, you need to check the type of connectors your soundboard uses for its main stereo outputs, as well as what your amplifier uses for inputs. Recommended Reading: How to Connect Two Amps Together: A Quick Step-By-Step Guide 1. Fortunately, connecting your audio board to an amplifier is quite easy and straightforward. Watch How to Connect the Mixer to the AmplifierĪn audio mixing board does not have enough power for speakers, so if you want to fill a room or reach an audience you will need to use an external power amplifier and PA (Public Address) speakers.Troubleshooting – I’ve connected the amp to a mixer, but it doesn’t work.What Jacks should I use to connect the Mixer to My Amplifier?.Variation 3: Connecting to Monitor Speakers /Amplifiers.Variation 2: Connecting to a Home Stereo Amplifier.Variation 1: Connecting to Powered Speakers.( you can use paint with different colors to show me how it should be connected or draw a scematic ) any help really would be a godsend. Other then my recordplayer i have 0 clue on how to hook up my other stuff ive tried a few thing but in the end one of the functions always doesnt work. A few days ago i purchased two tape decks one of wich was acompanied by an equaliser and an amplifier. Recently I’ve obtained an interest in collecting older audio equipment.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |